How to make a moving mouth sheep puppet (Bobby)

Baaaaah, Behhhh. In this tutorial, we’ll talk about how to build Bobby, a moving mouth sheep puppet with arm rods. Bobby is based on the prototype Mac and Cheese which we’ve talked about how to build earlier. It is structurally very similar except with more decorations. The major difference is that the mouth is built seperately and then attached to the outside instead of inserted inside. This tutorial is therefore going to focus on the things that’s different from the prototype.

Here’s a list of materials used, followed by the steps:

1. Build the basic structure: Like how we built Mac and Cheese and Bottle Monster, you want to fold the fabric over, trace the pattern, sew it up, and flip it over. For more detailed instructions please look at step 1-5 of the How to build Mac and Cheese tutorial.

2. Build the mouth: First we need to cut cardboard into the shape of a mouth board (pic 2a), and then we glue felt on it so it doesn’t look like a piece of cardboard. In the last two puppets we used black fabric for the mouth. This time I thought I would try red felt for a change.

And now it’s time for the exterior portion of the mouth. In pic 2b, you can see that I started gluing some fabric to make the jaw. In pic 2c, you can see the jaw is done. In pic 2d, the upper part is also done. Notice that you are only gluing the edges of the fabric. You want to have space between the fabric and the cardboard. You are creating pockets so that you can put your hand inside to manipulate the mouth. Also it makes the mouth look more three dimensional. The mouth part is done by now. Sure, it doesn’t look like a sheep yet, but already you have a mouth to play with!

3. Glue jaw to the bottom of the face: In the previous two tutorials, we cut a slit across the head/face portion of the basic structure and then put in the mouth. This time, we have not only the mouth but also the face to put in. So we cut out a circle instead of just a slit. Now you want to glue the the jaw to the lower portion of the circle. There should be space between the upper portion of the circle and the upper portion of the mouth, because we still need to put in the rest of the face, such as eyes.

4. Put in the upper half of the face: This will be the flat part of the face (unlike the mouth, which is the protruding part). First cut out a piece somewhat larger than the area you are covering (pic 4a). And then glue the top of the fabric to the top portion of the circle cut out (pic 4b). And once you are done, glue the side to the side of the circle, and the bottom of the fabric to the top of the mouth. By now, the basic structure, the mouth we made earlier, and this new piece of fabric we put in to be the mouth should all be connected. Then we put in the eyes. Now we basically the head done (pic 4d).

For the last two puppets I draw eyes on index cards and then cut them out. This time I decided to try something different. In pic 4c you see these plastic craft/stuffed animal eyes that you can purchase at craft stores. The way you install it is simple. First drill a hole wherever you want the eye installed. Stick the screw looking part (the black piece in this picture) into the hole, and hold the washer looking part (the white piece) behind the hole so the two pieces fit together, sandwiching the fabric (which is the face) in between. Please make sure you already planned out where the eyes are going to go, because once these things are installed, it’s very hard to get them off without breaking things.

5. Put in the ears: First cut out the ear shape out of the fur babric (pic 5a). And then you can glue on a smaller piece that’s not furry to create the inside of the ear (pic 5b). Of course, this is not required but this gives the puppet more personality (or sheeponality). Before I installed the ears, I first decided to pinch parts of the back of the head (pic 5c) and sew them together. This is to make the head smaller. In the last two puppets, the head space is shared by some polyfil and the mouth board. However, with this puppet, the mouth protrudes and doesn’t take up head space. That’s why I am making the head smaller. And then you can glue on the ears. When you are done, you have something like pic 5d. And all that’s left to do is put on the arms.

6. Make the arms and rods: First make the arms. The arms are just two tubes made from two strips of fabric folded over and sewn together. Sew or glue these two tubes onto the main body of the puppet and stuff in some polyfill to give it some volume (muscles, if you will). Pic 6a wasn’t quite clear so you’ll have to use your imagination.

And then you want to drill a hole towards the end of the arm (near where the hand/hoof will be). This is for the rod to go through (pic 6b). Then we make the arm rod. I glued a piece of cardboard on top of a bamboo skewer so the rod would stay in place (pic 6c). Then you want to put the rod through the hole we’ve just drilled (pic 6d). And finally we take a piece of fabric to seal the arm tube. This has two purposes. One is to give it the hand/hoof look. And another was to seal that piece of cardboard in so our rod doesn’t slide out of the tube. And now you are done!

Oh wait, one more step. The head might be a little empty at this point, and when you touch the top of the head, it just sinks in. All you have to do is make a little pouch/bag, put some polyfill in it, and stick it into the head. I don’t even seal it, because sometimes I would like to take the bag out to adjust the amount and shape.

And that’s how you build Bobby!

More puppet building tutorials:
How to make a moving mouth puppet with arm rods (Mac and Cheese)
How to make a moving mouth puppet with glove hands (Bottle Monster)

List of videos Bobby has appeared in so far:
Episode 12: Daylight Saving
Episode 11: The Truth Behind Halloween
Episode 10: Silent Sneeze
Episode 9: Wordcraft
Episode 8: Nobody’s Watching
Video Special: Obscure UCLA Facts You Did Not Know
Episode 6: Dance, Dance, Dance
Episode 5: Amazing Grass